P side				N side							Vi Nham Results (Raw data from May 13th, 2007)
	Ladder position	Low voltage power supply				Low voltage power supply				Biasing Voltage	Leakage current	comments	Pside	Nside	comment
		Voltage (V)	Current (A)	Voltage (V)	Current (A)	Voltage (V)	Current (I)	Voltage (V)	Current (A)	(V)	(µA)
top 3 ladders sector	20	-2.2	1.7	2	0.45	-2.1	1.6	2	0.5	30	120	module 15P one Alice128 bad	4P one bad alice	ok	High voltage trip
	1	-2.2	1.6	2	0.44	-2.2	1.6	2	0.47	50	45	Pside perfect, problem with the digital output on Nside : the most significant bit is oscillating	Pside OK	Nside OK
	2	-2.2	1.6	2	0.49	-2.2	1.66	2	0.48	30	800	modules ok (Pside and Nside), leakage current to high, HV coupling capacitors need to be changed	4P weird data	ok	High voltage trip
North 7 ladders sector	3	-2.2	1.45	2	0.45	-2.2	1.5	2	0.44	25	136	JTAG problem with 11P, 14P and 1N,.	11P OK	OK	high voltage trip
	4	-2.2	1.6	2	0.46	-2.2	1.56	2	0.48	30	110	JTAG problem with 12P	12P OK	ok
	5	-2.2	1.54	2	0.46	-2.2	1.58	2	0.45	30	106	JTAG problem with 1P	OK	OK
	6	-2.2	1.59	2	0.47	-2.2	0	2	0	30	91	Nside not responding, Pside OK	OK	Dead
	7	-2.2	1.65	2	0.5	-2.2	1.53	2	0.45	35	144	JTAG problem with 13N, Pside no data	Dead	Dead
	8	-2.2	0	2	0.02	-2.2	1.59	2	0.44	40	135	Pside ok at the begining, then datas are degrading. High current on the +2V : probably it comes from the output currrent of the ALICE128 output buffer. After waiting for a while, it is ok again and starts to degrade again	OK, 8P noisy	Noisy with pedestal variation
	9	-2.2	1.59	2	0.47	-2.2	1.6	2	0.45	50	174	power supply connector problem on Pside	7P with dead strips	OK
bottom 3 ladders sector	10	-2.2	1.67	2	0.54	-2.2	1.5	2	0.45	30	220	module 7N not responding with JTAG, biasing current to high	8P: pedestal value higher than 255, 4P pedestal value strange	ok	High voltage trip
	11	-2.2	1.65	2	0.52	-2.2	1.58	2	0.49	40	72	module 9N not responding with JTAG	OK	ok
	12	-2.2	1.64	2	0.49	-2.2	1.59	2	0.46	40	77	good ladder	OK	OK
South 7 ladders sector	13	-2.2	1.65	2	0.49	-2.2	1.6	2	0.46	30	240	Data problem with 6P, biasing current to high	problem with 6P	ok	High voltage trip
	14	-2.2	1.6	2	0.47	-2.2	1.44	2	0.44	30	180	JTAG problem with 15N and 16N.	OK	data problem with 15N (while OFF)
	15	-2.2	1.54	2	0.47	-2.2	1.6	2	0.47	30	125	HV and LV connection to be checked side P. Pedestal high with 16P	Pside noisy	ok
	16	-2.2	1.11	2	0.36	-2.2	1.49	2	0.43	30	173	JTAG problem with 4P, 5P, 7P, 8P, 12P, 13P, 1N, 10N.	4P, 7P, 8P, 13P OK, but no data from 12P	10N ok
	17	-2.2	1.52	2	0.46	-2.2	1.55	2	0.44	30	144	JTAG problem with 5P. HV connection to be checked.	5P forced (on May 16th)	OK
	18	-2.2	1.6	2	0.46	-2.2	1.59	2	0.45	30	137	good ladder	OK	11N dodgy
	19	-2.2	1.44	2	0.48	-2.2	1.64	2	0.42	30	174	JTAG problem with 13P. No data with 11P because power supply disconnected by latchup detection.	OK	6N high pedestal, 11N noisy